Dokio 80W (40*2pcs) 18V Flexible Foldable Solar Panel + 12V/24V Solar Controller Portable Solar Panel For Camping/Travel
|45 days Money back Returns accepted if product not as described, buyer pays return shipping; or keep the product & agree refund with seller.|
Guarantees: On-time Delivery 60 days
DOKIO Basic characteristics of the product
|Open circuit voltage||Voc||21.60V|
|Maximum power point voltage||Vmpp||18.00V|
|Short-circuit current||I sc||4.60A|
|Maximum power point current||I mpp||4.44A|
PERFORMANCE AT 1000 W/ M⊃2;, NOCT, AM 1.5
Minor reduction in efficiency under partial load conditions at 25°C: at 100 W/m2, 95%- (+/-3%) of the STC efficiency (1000 W/m2) is achieved.
|Maximum system voltage SC II||1000 V||Maximum reverse current||16 A|
|Maximum system voltage USA NEC||600 V||Increased snowload acc. to IEC 61215||5.4 kN/m⊃2;|
|PTC rating||90 W||Module efficiency||17.0%|
|Junction box||IP65||DOKIO Plus-Sorting*||Pflash ≥ Pmax|
|Connector||SAE Connecor||Power tolerance*||+/- 3 %|
DOKIO Product Show
Build your own solar system
Operating Instruction for Solar Panel
- Installation and operation of solar cell module
- a). Climatic Conditions
- Install PV module according to the following conditions
- Ambient Temperature: －20℃ to ＋ 40℃.
- Operating Temperature: －20℃ to ＋ 80℃.
- Borne Snow Pressure: less than 2000Pa
- Borne Wind Pressure: less than 3000Pa
- Water proof: don’t soak the PV module in water or continuously expose it to the sprinkling device or under fountains.
- Corrosion resistance: except for corrosive salt area and sulfurous area.
- b). Direction
- Module shall be installed facing south (northern hemisphere) or north (southern hemisphere).Facing east or west may send only a relatively small amount of electric energy, and incorrect installing orientation will cause a loss in energy output.
- Series-connected PV module shall be installed in the same direction and with the same angle, because different directions and angles may cause loss of energy due to the differences of solar radiation.
- Installation of module shall avoid under shadows. Even though the module decreases loss of energy through bypass diode, the shadow will cause loss in energy output.
- Under normal circumstances, the module generates more current and voltage in routines than in the standardized testing conditions, therefore, please operate the configuration by multiplying 1.25 times of the short-circuit current and open-circuit voltage during the installation and application.
- c). Installation and Precautions
- The module must be installed on the roof with fire proof function.
- Connector for installation and connection needs to obtain the approved certification of connector (VDE V 0126-3).
- Junction box with the type required by the installation and connection needs to obtain the approved certification of junction box (2 PFG1162).
- Cables with the type required by the installation and connection need to obtain the approved certification of cables (2 PFG1161).
- When installing modules in batches, the interval distance between modules shall be larger than 100mm.
- Firstly, place the solar cell module with certain angle (generally 30° or 45°in horizontal plane), and choose a direction that can let the sunlight directly radiate the solar cell module for more time to place the module.
- Module and bracket shall be fully contacted with the ground.
- When installing modules, keep away from ignition source or fuels.
- Installation structure and bracket must bear external pressures such as wind pressure and snow pressure.
- Installation structure shall be environment resistant and chosen appropriate materials and preservative treatment.
- Method for high altitude installation shall be appropriate.
- High falling may cause death, disability and damages.
- It is forbidden to disassemble, bend, toss the module, nor shock it by hard objects or walk on it.
- d). Wire Connection and Precautions
- Open the junction box, connect the red wire to the positive pole (+) and the black wire to the negative pole (-) and insert the other end to the interface of the solar cell wire of the battery cabinet.
- Fasten the module on the bracket by fastening piece and module mounting hole, the hardness and intensity of the fastening piece and module bracket must achieve the standard and be in accordance with relevant requirements.
- Use the private joint provided by the company.
- Note: short-circuit for positive and negative poles are forbidden.
- The joint shall be tightened without any clearances; otherwise, the clearances may cause sparks.
- Check if the fastening part of the installation structure is loosen; otherwise, it must be tightened.
- Often clear the dust and dirt on the surface of the PV module with soft cloth to prevent the loss in energy output due to the block on the surface of the module. Check frequently if the surface of the module is blocked by objects.
- Replace modules with the same specifications and the same type products.
- Be careful not to contact the exposed part of the wire or joint, and if it is necessary, wear the insulator (such as tools, gloves, etc.).
- During the process of installation and maintenance, be sure to cover the surface of the module with cloth or other light proof materials, because the module will generate high voltage under solar radiation which would be dangerous.
Through the highest standards of European testing
Our strength guarantees quality and quantity
Strict and testing
Warehouse Sales Show
0 out of 5 (0 Ratings)
|Positive (0 %)||
4 Stars (0)
|Shipping Company||Shipping Cost||Estimated Delivery Time|
|3 - 7 days|
|3 - 7 days|
|5 - 14 days|
|Post Air Mail||Free Shipping||15 - 45 days|
|Return Policy||If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.
N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
|Seller Service||On-time DeliveryIf you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).|
12V Car LED Courtesy Door Projector Light For Audi A3/A4/A6/VW/Skoda Foot Nest Lights Led trunk Luggage Light Lamp 6500K White
US $10.00 / lot
51Pcs DIY Micro Landscapes Dollhouse Bonsai Figurine Miniature Decoration Ornament For Potted Plant Craft Home Garden Home Decor
US $17.35 / piece
HD Digital Ku Band LNB For Satellite TV Receiver High Gain Low Noise Universal 8 LNB
US $32.00 / piece
beler Car 2.5 inch H1 2 pin Right And Left Mini HID Low High Beams Bi-xenon Projector Halo Lens Kit with Clear Headlight Shroud
US $28.99 / piece
LEORY 6V 1.2W Solar Panel Polycrystalline Solar Cell Module Durdable Waterproof Charger Emergency Light Camping
US $8.45 / piece
1.8inch Bixenon HID Headlight Projector Lens Mini Gatling Gun Projector Shrouds For Cars Motorcycle H7 H4 H1 xenon kit Modify
US $42.50 / piece
online shopping, buying directly from manufacturers?
- Go to Alibaba.com and enter the wanted item into search field.
- Having made your choice, click "Contact supplier" button on the right
- On the next page enter your request and click "Send" button.
- Upon clicking you will be asked to get registered. Do it and wait for the reply.